Colnago Ovalmaster 2000 titanium frameset, 54cm CT
- Thread starter plasma2873
- Start date
plasma2873
Kona Fan
Colnago Ovalmaster
I've had a lot of interest in the frame but it's still available. If anybody wants to make me an offer I'll consider it, otherwise it will go in Cycling weekly in the next few weeks. New family addition forces sale.
Best wishes,
Stuart
I've had a lot of interest in the frame but it's still available. If anybody wants to make me an offer I'll consider it, otherwise it will go in Cycling weekly in the next few weeks. New family addition forces sale.
Best wishes,
Stuart
plasma2873
Kona Fan
Colnago measurements
For those who asked, the exact measurements are as follows
Seat tube, centre to top 550mm
Seat tube, centre to centre 520mm
The top tube is a deep octagonal (master) section, hence the 30mm difference
Top tube is 540mm centre to centre.
Steerer has 195mm of shaft.
Head tube is 125mm long
As with all Colnagos (until recently) the forks are 1 inch. I have the necessary adapter to use 1 1/8 stems included with the 110mm Colnago stem which can also be purchased. I'll leave 20mm of aluminium spacers and the Campagnolo Chorus headset fitted.
Bottom bracket is Italian thread. I had a Shimano triple fitted. I measure the bootom bracket shell width to be 71mm.
Seat tube external diamater 31.8mm, internal diameter looks to be 30mm (very hard to measure without calipers). I have the previously fitted carbon seatpost if required. The tube wall thicknesses are very thin as you would expect from Ti 6Al/4V.
The frame has a brazing for the front mech. I'll also leave on the Dura ace cable stops and adjusters.
Postage outside the UK will be expensive (and slow). I'm guessing around 75 euros or maybe greater.
I'm afraid I have no scales to record the frame and fork mass. Sorry.
Best wishes, Stuart
For those who asked, the exact measurements are as follows
Seat tube, centre to top 550mm
Seat tube, centre to centre 520mm
The top tube is a deep octagonal (master) section, hence the 30mm difference
Top tube is 540mm centre to centre.
Steerer has 195mm of shaft.
Head tube is 125mm long
As with all Colnagos (until recently) the forks are 1 inch. I have the necessary adapter to use 1 1/8 stems included with the 110mm Colnago stem which can also be purchased. I'll leave 20mm of aluminium spacers and the Campagnolo Chorus headset fitted.
Bottom bracket is Italian thread. I had a Shimano triple fitted. I measure the bootom bracket shell width to be 71mm.
Seat tube external diamater 31.8mm, internal diameter looks to be 30mm (very hard to measure without calipers). I have the previously fitted carbon seatpost if required. The tube wall thicknesses are very thin as you would expect from Ti 6Al/4V.
The frame has a brazing for the front mech. I'll also leave on the Dura ace cable stops and adjusters.
Postage outside the UK will be expensive (and slow). I'm guessing around 75 euros or maybe greater.
I'm afraid I have no scales to record the frame and fork mass. Sorry.
Best wishes, Stuart
plasma2873
Kona Fan
Colnago ovalmaster
Just a reminder, sale is for frame and fork only. No groupset, parts or wheels are included.
I've not been able to upload any pictures of the frame only, but maybe able to on Monday. The only marks are to the paint inside the left hand chainstay and just a couple of chips on the right hand chain stay, normally obscured by the chainset.
Regards,
Stuart
Just a reminder, sale is for frame and fork only. No groupset, parts or wheels are included.
I've not been able to upload any pictures of the frame only, but maybe able to on Monday. The only marks are to the paint inside the left hand chainstay and just a couple of chips on the right hand chain stay, normally obscured by the chainset.
Regards,
Stuart
plasma2873
Kona Fan
Colnago Ovalmaster
Bump
Bump
plasma2873
Kona Fan
Colnago oval master - SOLD
The frame has now been sold, many thanks for your interest.
Regards,
Stuart
The frame has now been sold, many thanks for your interest.
Regards,
Stuart
Similar threads
