2000 Gary Fisher Supercaliber. Finished ! !
- Thread starter Mike Muz
- Start date
- Feedback
- View
Re: 2000 Gary Fisher Supercaliber
When will you buy a frame that fits?
When will you buy a frame that fits?
Re:
Suits me. That's all that counts.
Here's one your size
viewtopic.php?f=2&p=2700484#p2700484
Mike
Suits me. That's all that counts.
Here's one your size
viewtopic.php?f=2&p=2700484#p2700484
Mike
Re:
Bare frame, with gear hanger, weighs in at smack on 1.5kg.
Started on it today. I wanted to test the yellow paint on an area before doing the main tubes. It's quite a pale yellow, with some flecks in it, almost metallic.
So, rubbed down, primered, and a bit of yellow later,
IMG_0791 by Michael Murray, on Flickr
Followed by clear coat. Sadly, it is a bit too pale. :roll: So won't be using any more of that I think. Although I will have a proper look at it in daylight tomorrow.
A couple of the bottle bosses were spinning, so I pushed them through into the tubes, before rattling them out.
IMG_0807 by Michael Murray, on Flickr
New ones to replace,
IMG_0808 by Michael Murray, on Flickr
Simply put it in the hole, hold the nut and tighten the allen bolt.
IMG_0810 by Michael Murray, on Flickr
Simples
IMG_0811 by Michael Murray, on Flickr
May look in my stash for some stickers to cover missing paint. I would still like to have a go at the red though. Look s like it's been leant against a lamp post or something similar.
Mike
Bare frame, with gear hanger, weighs in at smack on 1.5kg.
Started on it today. I wanted to test the yellow paint on an area before doing the main tubes. It's quite a pale yellow, with some flecks in it, almost metallic.
So, rubbed down, primered, and a bit of yellow later,
IMG_0791 by Michael Murray, on FlickrFollowed by clear coat. Sadly, it is a bit too pale. :roll: So won't be using any more of that I think. Although I will have a proper look at it in daylight tomorrow.
A couple of the bottle bosses were spinning, so I pushed them through into the tubes, before rattling them out.
IMG_0807 by Michael Murray, on FlickrNew ones to replace,
IMG_0808 by Michael Murray, on FlickrSimply put it in the hole, hold the nut and tighten the allen bolt.
IMG_0810 by Michael Murray, on FlickrSimples
IMG_0811 by Michael Murray, on FlickrMay look in my stash for some stickers to cover missing paint. I would still like to have a go at the red though. Look s like it's been leant against a lamp post or something similar.
Mike
Re:
Starting to wish I'd done the same, and stickered over the gnaarly bits!
Anyway, after a bit of paint and lacquer, the yellow is finally done.
IMG_0890 by Michael Murray, on Flickr
The finish is great, but underneath, it is far from perfect. The only way around that would be to have taken it back to bare metal, I think.
IMG_0892 by Michael Murray, on Flickr
Now for the tricky unmasking, nervous. Should I need to cut around the tape first?
Mike
Starting to wish I'd done the same, and stickered over the gnaarly bits!
Anyway, after a bit of paint and lacquer, the yellow is finally done.
IMG_0890 by Michael Murray, on FlickrThe finish is great, but underneath, it is far from perfect. The only way around that would be to have taken it back to bare metal, I think.
IMG_0892 by Michael Murray, on FlickrNow for the tricky unmasking, nervous. Should I need to cut around the tape first?
Mike
Re:
Masking came off easily, big relief
IMG_0896 by Michael Murray, on Flickr
IMG_0897 by Michael Murray, on Flickr
IMG_0898 by Michael Murray, on Flickr
So, now for the red
Mike
Masking came off easily, big relief
IMG_0896 by Michael Murray, on Flickr
IMG_0897 by Michael Murray, on Flickr
IMG_0898 by Michael Murray, on FlickrSo, now for the red
Mike
