Rim wear, is this too much?

Qebrus · Dec 5, 2020

Hello,

I am currently rebuilding and upgrading a few parts on a lovely 1995 rockhopper, I’m coming to the end of the project and am now working on the wheels.

I have a question regarding the brake tracks on these Araya 26x1.5 rims, I have held a straight edge to the rim and can see a slight amount of concave to the surface. Now to my untrained eye they don’t seem to be too bad and “hopefully” still have some life in them as I am not in a position to be buying a new wheelset at the minute.

Thanks!

konacarl · Dec 5, 2020

Some model Arayas were built concave. Check the archive on here to see if yours are some.

FluffyChicken · Dec 5, 2020

Which Araya rims are they, this could well be one of their technologies, depending on year. Campag did similar.
It looks normal.
full picture too.

Qebrus · Dec 5, 2020

konacarl":2jspl9dp said:
Some model Arayas were built concave. Check the archive on here to see if yours are some.

Yes I had seen some of their books on their I shall have a look!! Feeling slightly more relived now!

Qebrus · Dec 5, 2020

FluffyChicken":2wbspm34 said:
Which Araya rims are they, this could well be one of their technologies, depending on year. Campag did similar.
It looks normal.
full picture too.

They are the Araya 26x1.5 HE GP-710, was that a full picture you wanted uploaded sorry?

pete_mcc · Dec 5, 2020

Re:

Old school Arayas were built strong so I wouldn’t worry too much.
The RM400 were concave but markedly so, like the Camap Ataks and sthenos. Yours don’t look like they were made that way as the curve is uneven and not marked

Qebrus · Dec 5, 2020

Re: Re:

pete_mcc":2fdsf0il said:
Old school Arayas were built strong so I wouldn’t worry too much.
The RM400 were concave but markedly so, like the Camap Ataks and sthenos. Yours don’t look like they were made that way as the curve is uneven and not marked

Yes you are probably right no that I have a feel it definitely doesn’t feel as though it would have come from the factory like this. I’ll go ahead and assume they are safe to ride then at least until I find something to replace them when I have a little more money to spend on the build!

madjh · Dec 6, 2020

That is ok, but you can measure the thicknes with a caliper. Normal wear, next time don´t brake and will last for ever

And I say it is wear because it is not uniform. But can be what other people have said.

FluffyChicken · Dec 6, 2020

Re: Re:

pete_mcc":3d7g9uqr said:
Old school Arayas were built strong so I wouldn’t worry too much.
The RM400 were concave but markedly so, like the Camap Ataks and sthenos. Yours don’t look like they were made that way as the curve is uneven and not marked

Most of the range at the time was concave, some quite subtle, often a flick near the tyre edge of the rim.

But this rim ( new for 1993) was one of the few not designated concave.

Qebrus · Dec 6, 2020

The plan now is give these brake surfaces a good clean, any recommendations? I was planning to wipe down with some isopropyl. Going to get some new, either Swiss stop or Koolstop soft pads to further minimise wear for the foreseeable.

Rim wear, is this too much?

Qebrus

Dirt Disciple

konacarl

FluffyChicken

Qebrus

Dirt Disciple

Qebrus

Dirt Disciple

pete_mcc

Qebrus

Dirt Disciple

madjh

FluffyChicken

Qebrus

Dirt Disciple

Similar threads

Latest posts