Wanted Syncros stem - 100mm or less

Corbeau

Devout Dirtbag
Looking for a Syncros ahead stem, 1-1/8”, ideally shorter so 100mm or less with some angle, 10 degrees or a bit more is fine. Let me know what you have!
 
I dont have a syncross Corbeau,I have got a very nice Syntace,over £100 when I bought it new.It’s 110mm so a bit long but take a look anyway
 

Attachments

  • FC159292-8923-4DA9-8B89-395C75FFB7A1.webp
    FC159292-8923-4DA9-8B89-395C75FFB7A1.webp
    144.1 KB · Views: 2
  • 9B5C74D8-F1F2-421B-9432-0927D5541CF0.webp
    9B5C74D8-F1F2-421B-9432-0927D5541CF0.webp
    132 KB · Views: 2
  • 06F44A54-B522-445B-AA5E-453C56194626.webp
    06F44A54-B522-445B-AA5E-453C56194626.webp
    156.8 KB · Views: 1
  • 7E214029-9299-43D0-A4F4-099BF74A30BE.webp
    7E214029-9299-43D0-A4F4-099BF74A30BE.webp
    107.8 KB · Views: 2
Thanks Jaycee, but I’m holding out for Syncros. I found a post, and I’d love to match it with a stem on my 94 Marin. I have a nice Titec that’s 110 that I’ll likely post, and may have a matching post as well…
 
I was just about to list this when I saw your post. If you still need a Syncros stem I have a 110mm 1 1/8 Cattleprod that is in pretty dang good shape. It comes with the elusive top cap. It has some angle to it so maybe this could work for you even though it’s a bit longer than you wanted. This was on my Klein but I found it to be a tad too long for me so I swapped it out. PM me if this works for you and you still need one. I’m away for a week but I could post this when I get back next Monday if you wish.
 

Attachments

  • IMG_1192.webp
    IMG_1192.webp
    385.5 KB · Views: 4
  • FullSizeRender.webp
    FullSizeRender.webp
    522.9 KB · Views: 4
  • IMG_1190.webp
    IMG_1190.webp
    394 KB · Views: 7
  • IMG_1193.webp
    IMG_1193.webp
    561.7 KB · Views: 7
  • FullSizeRender.webp
    FullSizeRender.webp
    489.9 KB · Views: 8
That's not 110, that's about 130mm, possibly getting to a 140mm.
But hard to tell exactly from the tape measure.


To get a 110mm Syncos in the retro style you'll really be looking to the late 90s (GT era) probably matt finish.
Hinged high rise will be more common in that length from the DH side.

Though there should be a few 110mm normal style from, the tiny sized (15" maybe) bikes, I've not seen many about.
100mm on the other hand will certainly be a DH aimed hinged stem, in matt or silver from the end of the 90s.
 
Last edited:
That's not 110, that's about 130mm, possibly getting to a 140mm.
But hard to tell exactly from the tape measure.


To get a 110mm Syncos in the retro style you'll really be looking to the late 90s (GT era) probably matt finish.
Hinged high rise will be more common in that length from the DH side.

Though there should be a few 110mm normal style from, the tiny sized (15" maybe) bikes, I've not seen many about.
100mm on the other hand will certainly be a DH aimed hinged stem, in matt or silver from the end of the 90s.
Apologies if I’m incorrect. I measured from the middle of the clamp to the weld.
 
It is middle of the steerer hole to middle of the bar hole.
Advantage of laying a tape measure down :-)


As far as I know some, most?, do this as actual measurement, some do this as effective horizontal (zero degree) measurement.
Can't remember what Syncros use, always seems to have been actual. But then most have been Zero degree.
 
Thanks for thinking of me! That is too long for what I’m looking for. I’m still looking for something though, and open to options as long as they’re shorter….. I have a quill stem in 1-1/8” if folks are looking. It’s 120mm if memory serves.
 
Back
Top