Retrobike Forum Index

It is currently Tue Mar 02, 2021 2:40 am

* Login   * Register * Search  * FAQ



Post new topic Reply to topic  [ 57 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6  Next
Author Message
 Post subject: Re:
PostPosted: Tue Apr 21, 2020 11:34 pm 
retrobike rider / Gold Trader
retrobike rider / Gold Trader
User avatar

Joined: Fri Feb 06, 2009 11:13 pm
Posts: 11984
Location: Skipton
Member justbackdated used to sortPace forks and think Pace will still sell you elastomers. Hope so cos I need some!


Top
 Profile  
 
PostPosted: Thu May 14, 2020 11:39 am 
Old School Hero
User avatar

Joined: Wed Mar 27, 2013 1:32 am
Posts: 157
Location: Anglesey, N. Wales
Following this one...… ;-) there seems to be a few of us on similar builds at the moment. It will be good to see how everyone progresses.
The lacquer I've stripped, well most of it and the rubbing down has commenced (oh the joys) and polished up a few XT parts I have. My RC35's are being 'refreshed' and being rebuilt so things are coming along be it a bit slowly... must get a build thread going me thinks :-)


Top
 Profile  
 
 Post subject: Re:
PostPosted: Thu May 14, 2020 11:57 am 
BoTM Winner
BoTM Winner

Joined: Mon Sep 10, 2012 5:21 pm
Posts: 1065
Location: Hartlepool, County Durham
Cheers fellas....

Ok so I’m about to start the frame strip (of laquer) and decals here from Gil. I’ve already sourced a full period XT grouppo inc hubs on Mavic rims.

Will sort the frame and start to rebuild it. Once done I’ll get in with the forks....

Not sure what to do re headset? It’s 1 and 1/4. I try to fit new headsets each time I do a full rebuild however as these are rare size I might try servicing it with new bearings...


Top
 Profile  
 
PostPosted: Thu May 14, 2020 12:12 pm 
Retro Guru
User avatar

Joined: Mon Jun 19, 2017 7:01 pm
Posts: 1444
There are a few 1 1/4's on ebay if the stack heights right.


Top
 Profile  
 
 Post subject: Re:
PostPosted: Wed May 20, 2020 8:07 pm 
BoTM Winner
BoTM Winner

Joined: Mon Sep 10, 2012 5:21 pm
Posts: 1065
Location: Hartlepool, County Durham
So...

After around 5 coats of paint stripper over past few weeks (been busy at work!)...

It’s almost stripped!

I recon another coat should do it...

I recon once I get the decals on that my mojo to finish it will be back as laquer stripping is a laborious task.....


Attachments:
01091809-F62F-48B0-8B7C-C6E1267C8E54.jpeg
01091809-F62F-48B0-8B7C-C6E1267C8E54.jpeg [ 384.18 KiB | Viewed 680 times ]
381F44E4-97CA-4F79-A133-34BA7A84FD29.jpeg
381F44E4-97CA-4F79-A133-34BA7A84FD29.jpeg [ 323.85 KiB | Viewed 680 times ]
Top
 Profile  
 
PostPosted: Wed May 20, 2020 8:43 pm 
Gold Trader
Gold Trader
User avatar

Joined: Thu Oct 09, 2008 6:52 pm
Posts: 1217
Location: Cheshire
Doing a fine job there!

Looking forward to seeing this Elite back to its former glory. 8)

No pressure though, only a dozen or so elite owners eagerly watching you're every move!

:D


Top
 Profile  
 
 Post subject: Re:
PostPosted: Wed May 20, 2020 9:04 pm 
Old School Hero
User avatar

Joined: Wed Mar 27, 2013 1:32 am
Posts: 157
Location: Anglesey, N. Wales
I feel your pain.... just been through the very same process and it took a while but all good and ready to polish and decal up :) Seems we've similar builds in mind, looking forward to your seeing this come together for sure 8)


Top
 Profile  
 
PostPosted: Thu May 21, 2020 3:55 pm 
Retro Guru
User avatar

Joined: Mon Jun 19, 2017 7:01 pm
Posts: 1444
Just ordered my No Nonsense stripper :wink:


Top
 Profile  
 
PostPosted: Fri May 22, 2020 7:55 am 
BoTM Winner
BoTM Winner

Joined: Mon Sep 10, 2012 5:21 pm
Posts: 1065
Location: Hartlepool, County Durham
emjay wrote:
Doing a fine job there!

Looking forward to seeing this Elite back to its former glory. 8)

No pressure though, only a dozen or so elite owners eagerly watching you're every move!

:D



Made me laugh! .....

Ok so another coat of stripper yesterday followed by a blast with a pressure washer seems to have really done the majority of it now. The remaining small bits of laquer I think will need removing with wire wool prior to final polish with autosol. I bought a load of sponge mops off eBay for peanuts Which fit to a cordless drill which will work a treat and save a few hours. Hopefully do more today in the sun....

Top tip with the stripper Ross..... apply first coat, second after an hour to agitate then after another hour try a pressure washer on it... :wink:


Top
 Profile  
 
PostPosted: Fri May 22, 2020 3:42 pm 
Old School Hero
User avatar

Joined: Wed Mar 27, 2013 1:32 am
Posts: 157
Location: Anglesey, N. Wales
prezza wrote:

Top tip with the stripper Ross..... apply first coat, second after an hour to agitate then after another hour try a pressure washer on it... :wink:


2nd that, definitely give it a good dab and agitate well when applying the second coat, it really takes effect. Leave for a good hour plus again and blast off with a hose etc :)


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 57 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6  Next

All times are UTC [ DST ]


Who is online

Users browsing this forum: Google [Bot] and 58 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

About Us

Follow Retrobike

Other cool stuff

All content © 2005-2021 Retrobike unless otherwise stated.
Cookies Policy.
FatCOGS - Fat Chance Owner's Group

Powered by phpBB® Forum Software © phpBB Group