Retrobike Forum Index

It is currently Mon Mar 18, 2019 3:33 pm

* Login   * Register * Search  * FAQ

Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Thu Jun 20, 2013 6:20 pm 
Dirt Disciple

Joined: Wed May 15, 2013 11:06 am
Posts: 10
So I bought a headset along with a frameset, and didn't need to check for suitability as the seller did that for me.

Alas, a LBS cut my steerer tube too short while attempting to install the head set, and now I need a new headset with a lower stack height.

It's a one-inch threaded steerer, 24 TPI.
If it's relevant, the frame & forks are Columbus steel Fausto Coppi of around '95 vintage.
The outer diameter of the head tube is 31.8 mm, the inner I can't measure since there is a headset in place.

Now, stack height in this case is the total height of all the headset components that are left visible outside the head tube, right?

Measured like this, my current headset has a stack height of 40.00 mm, without any washers/spacers in place.
As it sits, the locknut doesn't go deep enough, the steerer tube is about 2mm too short even without a washer in the headset.

I know I will be needing a one-inch threaded headset - one with 38 mm stack height, including the locking washer- but what about
crown race diameter, S.H.I.S measurements all other measurements ( I don't even know what S.H.I.S stands for) ?

So what measurements am I going to need in order to choose the right headset?

I would love a Campagnolo headset, and one could be had reasonably on the web, but I'm afraid the 36.5 mm stack height might be too much (A new Campy Record 1" headset). Does that Campy stack height measurement include the washer below the locknut? I already have a beautiful Campagnolo engraved toothed washer I'd like to use, but it's 4 mm thick, which would likely mean the lock nut would not have enough thread to lock into..

PostPosted: Thu Jun 20, 2013 6:33 pm 
Old School Grand Master
User avatar

Joined: Fri Oct 14, 2011 8:41 pm
Posts: 9535
Location: Cumbria

Have a wander around the site, quite a few people have asked the question before like the above. You might have to give up on a campag road headset and settle for a Pista version.........or a headset with a small stack height like a Tange.

Or even try Hilary Stone..........


PostPosted: Thu Jun 20, 2013 11:57 pm 
rBoTM Winner
rBoTM Winner
User avatar

Joined: Wed Dec 12, 2012 10:18 pm
Posts: 2369
Location: California
The bike shop should buy you a fork!

PostPosted: Fri Jun 21, 2013 3:33 pm 
Retro Guru
User avatar

Joined: Wed Apr 25, 2012 2:08 pm
Posts: 2224
Location: Shrewsbury
Measure twice, cut once :facepalm:

PostPosted: Fri Jun 21, 2013 3:45 pm 
Retrobike's #1 Comedy Genius
Retrobike's #1 Comedy Genius
User avatar

Joined: Thu Jan 04, 2007 8:07 pm
Posts: 4104
Location: Wolkenkuckucksheim
TurboJ wrote:
.....LBS cut my steerer tube too short while attempting to install the head set...

Problem one, right there- if this is indeed the case, get them to supply you a new fork and fit it properly.

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC [ DST ]

Who is online

Users browsing this forum: DSH, Old Ned, otek59, Steve s and 9 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

About Us

Follow Retrobike

Other cool stuff

All content © 2005-2015 Retrobike unless otherwise stated.
Cookies Policy.
bikedeals - the best bike deals in one place
FatCOGS - Fat Chance Owner's Group

Powered by phpBB® Forum Software © phpBB Group